/* * File: TFT, keypad, DAC, LED, PORT EXPANDER test * With serial interface to PuTTY console * Author: Bruce Land * For use with Sean Carroll's Big Board * http://people.ece.cornell.edu/land/courses/ece4760/PIC32/target_board.html * Target PIC: PIC32MX250F128B */ //////////////////////////////////// // clock AND protoThreads configure! // You MUST check this file! #include "config_1_2_3.h" // threading library #include "pt_cornell_1_2_3.h" // yup, the expander #include "port_expander_brl4.h" //////////////////////////////////// // graphics libraries // SPI channel 1 connections to TFT #include "tft_master.h" #include "tft_gfx.h" // need for rand function #include // need for sin function #include //////////////////////////////////// // lock out timer 2 interrupt during spi comm to port expander // This is necessary if you use the SPI2 channel in an ISR. // The ISR below runs the DAC using SPI2 #define start_spi2_critical_section INTEnable(INT_T2, 0) #define end_spi2_critical_section INTEnable(INT_T2, 1) //////////////////////////////////// /* Demo code for interfacing TFT (ILI9340 controller) to PIC32 * The library has been modified from a similar Adafruit library */ // Adafruit data: /*************************************************** This is an example sketch for the Adafruit 2.2" SPI display. This library works with the Adafruit 2.2" TFT Breakout w/SD card ----> http://www.adafruit.com/products/1480 Check out the links above for our tutorials and wiring diagrams These displays use SPI to communicate, 4 or 5 pins are required to interface (RST is optional) Adafruit invests time and resources providing this open source code, please support Adafruit and open-source hardware by purchasing products from Adafruit! Written by Limor Fried/Ladyada for Adafruit Industries. MIT license, all text above must be included in any redistribution ****************************************************/ // string buffer char buffer[60]; //////////////////////////////////// // DAC ISR // A-channel, 1x, active #define DAC_config_chan_A 0b0011000000000000 // B-channel, 1x, active #define DAC_config_chan_B 0b1011000000000000 // DDS constant #define two32 4294967296.0 // 2^32 #define Fs 100000 //== Timer 2 interrupt handler =========================================== volatile unsigned int DAC_data ;// output value volatile SpiChannel spiChn = SPI_CHANNEL2 ; // the SPI channel to use volatile int spiClkDiv = 4 ; // 10 MHz max speed for port expander!! // the DDS units: volatile unsigned int phase_accum_main, phase_incr_main=400.0*two32/Fs ;// // DDS sine table #define sine_table_size 256 volatile int sin_table[sine_table_size]; void __ISR(_TIMER_2_VECTOR, ipl2) Timer2Handler(void) { int junk; mT2ClearIntFlag(); // main DDS phase and sine table lookup phase_accum_main += phase_incr_main ; DAC_data = sin_table[phase_accum_main>>24] ; // === Channel A ============= // wait for possible port expander transactions to complete while (TxBufFullSPI2()); // reset spi mode to avoid conflict with port expander SPI_Mode16(); while (SPI2STATbits.SPIBUSY); // wait for end of transaction // CS low to start transaction mPORTBClearBits(BIT_4); // start transaction // write to spi2 WriteSPI2( DAC_config_chan_A | ((DAC_data + 2048) & 0xfff)); while (SPI2STATbits.SPIBUSY); // wait for end of transaction // CS high mPORTBSetBits(BIT_4); // end transaction // need to read SPI channel to avoid confusing port expander junk = ReadSPI2(); // } // === print a line on TFT ===================================================== // print a line on the TFT // string buffer char buffer[60]; void printLine(int line_number, char* print_buffer, short text_color, short back_color){ // line number 0 to 31 /// !!! assumes tft_setRotation(0); // print_buffer is the string to print int v_pos; v_pos = line_number * 10 ; // erase the pixels tft_fillRoundRect(0, v_pos, 239, 8, 1, back_color);// x,y,w,h,radius,color tft_setTextColor(text_color); tft_setCursor(0, v_pos); tft_setTextSize(1); tft_writeString(print_buffer); } void printLine2(int line_number, char* print_buffer, short text_color, short back_color){ // line number 0 to 31 /// !!! assumes tft_setRotation(0); // print_buffer is the string to print int v_pos; v_pos = line_number * 20 ; // erase the pixels tft_fillRoundRect(0, v_pos, 239, 16, 1, back_color);// x,y,w,h,radius,color tft_setTextColor(text_color); tft_setCursor(0, v_pos); tft_setTextSize(2); tft_writeString(print_buffer); } // Predefined colors definitions (from tft_master.h) //#define ILI9340_BLACK 0x0000 //#define ILI9340_BLUE 0x001F //#define ILI9340_RED 0xF800 //#define ILI9340_GREEN 0x07E0 //#define ILI9340_CYAN 0x07FF //#define ILI9340_MAGENTA 0xF81F //#define ILI9340_YELLOW 0xFFE0 //#define ILI9340_WHITE 0xFFFF // === thread structures ============================================ // thread control structs // note that UART input and output are threads static struct pt pt_timer, pt_color, pt_anim, pt_key, pt_serial ; // The following threads are necessary for UART control static struct pt pt_input, pt_output, pt_DMA_output ; // system 1 second interval tick int sys_time_seconds ; // === Timer Thread ================================================= // update a 1 second tick counter static PT_THREAD (protothread_timer(struct pt *pt)) { PT_BEGIN(pt); // set up LED to blink mPORTASetBits(BIT_0 ); //Clear bits to ensure light is off. mPORTASetPinsDigitalOut(BIT_0 ); //Set port as output while(1) { // yield time 1 second PT_YIELD_TIME_msec(1000) ; sys_time_seconds++ ; // toggle the LED on the big board mPORTAToggleBits(BIT_0); // draw sys_time sprintf(buffer,"Time=%d", sys_time_seconds); printLine2(0, buffer, ILI9340_BLACK, ILI9340_YELLOW); // NEVER exit while } // END WHILE(1) PT_END(pt); } // timer thread // === Color Thread ================================================= // draw 3 color patches for R,G,B from a random number static int color ; static int i; static PT_THREAD (protothread_color(struct pt *pt)) { PT_BEGIN(pt); while(1) { // yield time 1 second PT_YIELD_TIME_msec(1000) ; // choose a random color color = rand() & 0xffff ; // draw color string tft_fillRoundRect(0,50, 150, 14, 1, ILI9340_BLACK);// x,y,w,h,radius,color tft_setCursor(0, 50); tft_setTextColor(ILI9340_WHITE); tft_setTextSize(1); sprintf(buffer," %04x %04x %04x %04x", color & 0x1f, color & 0x7e0, color & 0xf800, color); tft_writeString(buffer); // draw the actual color patches tft_fillRoundRect(5,70, 30, 30, 1, color & 0x1f);// x,y,w,h,radius,blues tft_fillRoundRect(40,70, 30, 30, 1, color & 0x7e0);// x,y,w,h,radius,greens tft_fillRoundRect(75,70, 30, 30, 1, color & 0xf800);// x,y,w,h,radius,reds // now draw the RGB mixed color tft_fillRoundRect(110,70, 30, 30, 1, color);// x,y,w,h,radius,mix color // NEVER exit while } // END WHILE(1) PT_END(pt); } // color thread // === Animation Thread ============================================= // update a 1 second tick counter static int xc=10, yc=150, vxc=2, vyc=0; static PT_THREAD (protothread_anim(struct pt *pt)) { PT_BEGIN(pt); while(1) { // yield time 1 second PT_YIELD_TIME_msec(32); // erase disk tft_fillCircle(xc, yc, 4, ILI9340_BLACK); //x, y, radius, color // compute new position xc = xc + vxc; if (xc<5 || xc>235) vxc = -vxc; // draw disk tft_fillCircle(xc, yc, 4, ILI9340_GREEN); //x, y, radius, color // NEVER exit while } // END WHILE(1) PT_END(pt); } // animation thread // === Keypad Thread ============================================= // Port Expander connections: // y0 -- row 1 -- thru 300 ohm resistor -- avoid short when two buttons pushed // y1 -- row 2 -- thru 300 ohm resistor // y2 -- row 3 -- thru 300 ohm resistor // y3 -- row 4 -- thru 300 ohm resistor // y4 -- col 1 -- internal pullup resistor -- avoid open circuit input when no button pushed // y5 -- col 2 -- internal pullup resistor // y6 -- col 3 -- internal pullup resistor // y7 -- shift key connection -- internal pullup resistor static PT_THREAD (protothread_key(struct pt *pt)) { PT_BEGIN(pt); static int keypad, i ; // order is 0 thru 9 then * ==10 and # ==11 // no press = -1 // table is decoded to natural digit order (except for * and #) // with shift key codes for each key // keys 0-9 return the digit number // keys 10 and 11 are * adn # respectively // Keys 12 to 21 are the shifted digits // keys 22 and 23 are shifted * and # respectively static int keytable[24]= // 0 1 2 3 4 5 6 7 8 9 10-* 11-# {0xd7, 0xbe, 0xde, 0xee, 0xbd, 0xdd, 0xed, 0xbb, 0xdb, 0xeb, 0xb7, 0xe7, // s0 s1 s2 s3 s4 s5 s6 s7 s8 s9 s10-* s11-# 0x57, 0x3e, 0x5e, 0x6e, 0x3d, 0x5d, 0x6d, 0x3b, 0x5b, 0x6b, 0x37, 0x67}; // bit pattern for each row of the keypad scan -- active LOW // bit zero low is first entry static char out_table[4] = {0b1110, 0b1101, 0b1011, 0b0111}; // init the port expander // Turn off the T2 ISR for a few microseconds start_spi2_critical_section; initPE(); // PortY on Expander ports as digital outputs mPortYSetPinsOut(BIT_0 | BIT_1 | BIT_2 | BIT_3); //Set port as output // PortY as inputs // note that bit 7 will be shift key input, // separate from keypad mPortYSetPinsIn(BIT_4 | BIT_5 | BIT_6 | BIT_7); //Set port as input mPortYEnablePullUp(BIT_4 | BIT_5 | BIT_6 | BIT_7); end_spi2_critical_section ; // the read-pattern if no button is pulled down by an output #define no_button (0x70) while(1) { // yield time PT_YIELD_TIME_msec(30); for (i=0; i<4; i++) { start_spi2_critical_section ; // scan each rwo active-low writePE(GPIOY, out_table[i]); //reading the port also reads the outputs keypad = readPE(GPIOY); end_spi2_critical_section ; // was there a keypress? if((keypad & no_button) != no_button) { break;} } // search for keycode if (keypad > 0){ // then button is pushed for (i=0; i<24; i++){ if (keytable[i]==keypad) break; } // if invalid, two button push, set to -1 if (i==24) i=-1; } else i = -1; // no button pushed // draw key number if (i>-1 && i<10) sprintf(buffer," %x %d", keypad, i); if (i==10 ) sprintf(buffer," %x *", keypad); if (i==11 ) sprintf(buffer," %x #", keypad); if (i>11 && i<22 ) sprintf(buffer, " %x shift-%d", keypad, i-12); if (i==22 ) sprintf(buffer," %x ahift-*", keypad); if (i==23 ) sprintf(buffer," %x shift-#", keypad); if (i>-1 && i<12) printLine2(10, buffer, ILI9340_GREEN, ILI9340_BLACK); else if (i>-1) printLine2(10, buffer, ILI9340_RED, ILI9340_BLACK); // NEVER exit while } // END WHILE(1) PT_END(pt); } // keypad thread //=== Serial terminal thread ================================================= static PT_THREAD (protothread_serial(struct pt *pt)) { PT_BEGIN(pt); static char cmd[30]; static float value; while(1) { // send the prompt via DMA to serial cursor_pos(4,1); red_text ; sprintf(PT_send_buffer,"cmd>"); // by spawning a print thread PT_SPAWN(pt, &pt_DMA_output, PT_DMA_PutSerialBuffer(&pt_DMA_output) ); clr_right ; normal_text ; //spawn a thread to handle terminal input // the input thread waits for input // -- BUT does NOT block other threads // string is returned in "PT_term_buffer" // !!!! --- !!!! // Choose ONE of the following: // PT_GetSerialBuffer or PT_GetMachineBuffer // !!!! --- !!!! PT_SPAWN(pt, &pt_input, PT_GetSerialBuffer(&pt_input) ); // // PT_GetMachineBuffer assumes a input // from a module, like GPS or Bluetooth // Terminate on key // PT_terminate_char = '\r' ; // PT_terminate_count = 0 ; // PT_terminate_time = 0 ; // --- // Terminate on '#' key // PT_terminate_char = '#' ; // PT_terminate_count = 0 ; // PT_terminate_time = 0 ; // --- // Terminate after exactly 5 characters // or // Terminate after 5 seconds PT_terminate_char = 0 ; PT_terminate_count = 5 ; PT_terminate_time = 5000 ; // note that there will NO visual feedback using the following function //PT_SPAWN(pt, &pt_input, PT_GetMachineBuffer(&pt_input) ); // returns when the thead dies on the termination condition // IF using PT_GetSerialBuffer, when is pushed // IF using PT_GetMachineBuffer, could be on timeout if(PT_timeout==0) { sscanf(PT_term_buffer, "%s %f", cmd, &value); } // no actual string else { // uncomment to prove time out works //mPORTAToggleBits(BIT_0); // disable the command parser below cmd[0] = 0 ; } switch(cmd[0]){ case 'f': // set frequency of DAC sawtooth output // enter frequecy in HZ cursor_pos(6,1); phase_incr_main = (int)(value*(float)two32/Fs); sprintf(PT_send_buffer,"DDS freq = %6.1f", value); // by spawning a print thread PT_SPAWN(pt, &pt_DMA_output, PT_DMA_PutSerialBuffer(&pt_DMA_output) ); clr_right ; cursor_pos(7,1); sprintf(PT_send_buffer,"DDS increment = %d", phase_incr_main); PT_SPAWN(pt, &pt_DMA_output, PT_DMA_PutSerialBuffer(&pt_DMA_output) ); clr_right ; break; case 't': // send the prompt via DMA to serial console sprintf(PT_send_buffer,"time = %d ", sys_time_seconds); // by spawning a print thread cursor_pos(9,1); PT_SPAWN(pt, &pt_DMA_output, PT_DMA_PutSerialBuffer(&pt_DMA_output) ); clr_right ; break; } // never exit while } // END WHILE(1) PT_END(pt); } // thread 3 // === Main ====================================================== void main(void) { //SYSTEMConfigPerformance(PBCLK); ANSELA = 0; ANSELB = 0; // set up DAC on big board // timer interrupt ////////////////////////// // Set up timer2 on, interrupts, internal clock, prescalar 1, toggle rate // at 30 MHz PB clock 60 counts is two microsec // 400 is 100 ksamples/sec // 2000 is 20 ksamp/sec OpenTimer2(T2_ON | T2_SOURCE_INT | T2_PS_1_1, 400); // set up the timer interrupt with a priority of 2 ConfigIntTimer2(T2_INT_ON | T2_INT_PRIOR_2); mT2ClearIntFlag(); // and clear the interrupt flag // control CS for DAC mPORTBSetPinsDigitalOut(BIT_4); mPORTBSetBits(BIT_4); // SCK2 is pin 26 // SDO2 (MOSI) is in PPS output group 2, could be connected to RB5 which is pin 14 PPSOutput(2, RPB5, SDO2); // 16 bit transfer CKP=1 CKE=1 // possibles SPI_OPEN_CKP_HIGH; SPI_OPEN_SMP_END; SPI_OPEN_CKE_REV // For any given peripherial, you will need to match these // NOTE!! IF you are using the port expander THEN // -- clk divider must be set to 4 for 10 MHz SpiChnOpen(SPI_CHANNEL2, SPI_OPEN_ON | SPI_OPEN_MODE16 | SPI_OPEN_MSTEN | SPI_OPEN_CKE_REV , 4); // end DAC setup // === build the sine lookup table ======= // scaled to produce values between 0 and 4096 int ii; for (ii = 0; ii < sine_table_size; ii++){ sin_table[ii] = (int)(2047*sin((float)ii*6.283/(float)sine_table_size)); } // === config threads ========== // turns OFF UART support and debugger pin, unless defines are set PT_setup(); // === setup system wide interrupts ======== INTEnableSystemMultiVectoredInt(); // init the threads PT_INIT(&pt_timer); PT_INIT(&pt_color); PT_INIT(&pt_anim); PT_INIT(&pt_key); PT_INIT(&pt_serial); // init the display // NOTE that this init assumes SPI channel 1 connections tft_init_hw(); tft_begin(); tft_fillScreen(ILI9340_BLACK); //240x320 vertical display tft_setRotation(0); // Use tft_setRotation(1) for 320x240 // seed random color srand(1); // round-robin scheduler for threads while (1){ PT_SCHEDULE(protothread_timer(&pt_timer)); PT_SCHEDULE(protothread_color(&pt_color)); PT_SCHEDULE(protothread_anim(&pt_anim)); PT_SCHEDULE(protothread_key(&pt_key)); PT_SCHEDULE(protothread_serial(&pt_serial)); } } // main // === end ======================================================